眾所周知,進口淮安NSK軸承是許多機械設備的核心部件,在機械設備中起著不可替代的作用.軸承會受到周圍環境的影響,使軸承受到不同程度的損壞,因此作為外部設備進口軸承也應給予相應的重視.

As we all know, imported Huaian NSK bearings are the core components of many mechanical equipment, and play an irreplaceable role in mechanical equipment. Bearings will be affected by the surrounding environment, so that bearings will be damaged to varying degrees, so as an external equipment imported bearings should also be given appropriate attention.

在常規檢查過程中,如發現軸承油量不足,應從注油口或油位孔注油.注意油位孔或油位已達到量規的極限.

In the course of routine inspection, if insufficient oil is found in the bearing, oil should be injected from the oil injection port or oil level hole. Note that the oil level hole or oil level has reached the limit of the gauge.

經檢查發現,當淮安NSK軸承需要更換機油時,應先將其排出.卸油溫度應達到40-50℃,在擾動下卸油.只有這樣,臟油才能被徹底排放和清潔.這樣,在潤滑油排放前,應先啟動滾輪的溫潤滑油,使熱油快速流出,使箱內雜質容易與潤滑油混合排出.

After inspection, it is found that when Huaian NSK bearings need to replace oil, they should be discharged first. The unloading temperature should reach 40-50 C and unload oil under disturbance. only in this way can dirty oil be thoroughly discharged and cleaned. In this way, before discharging the lubricating oil, the warm lubricating oil of the roller should be started to make the hot oil flow out quickly, so that the impurities in the box can easily be mixed with the lubricating oil and discharged.

但對于驅動橋,、輪行星減速器和勵磁油腔,由于其殼體的外露部分是旋轉的,在檢查油位或卸載,、加油時,需要打開一個思想裝置,將油孔的位置調整到合適的位置.

But for the drive axle, wheel planetary reducer and excitation oil chamber, because the exposed part of the shell is rotating, when checking the oil level or unloading, refueling, it is necessary to open an ideological device to adjust the position of the oil hole to the appropriate position.

還應注意,在油位檢查或灌裝時,油位可以達到油孔邊緣所指示的油位.

It should also be noted that during oil level inspection or filling, the oil level can reach the oil level indicated by the edge of the oil hole.

在使用變頻器的變速風扇中,破壞性的電流很可能流過軸承.這可能導致軸承過早失效和風扇關閉.使用絕緣淮安NSK軸承可以防止破壞性電流引起的故障.與其它絕緣方法相比,這種軸承結合了軸承的功能和電氣絕緣的功能,是一種經濟的解決方案.軸承內環或外環的外表面采用普通工藝涂覆氧化鋁,具有絕緣效果,不受高溫,、水汽和化學物質的影響.

In variable speed fans using transducers, destructive currents are likely to flow through bearings. This may lead to premature bearing failure and fan closure. Insulated Huaian NSK bearings can prevent faults caused by destructive current. Compared with other insulation methods, this kind of bearing combines the functions of bearing and electrical insulation, and is an economical solution. The outer su-ce of bearing inner ring or outer ring is coated with alumina by common process, which has insulation effect and is not affected by high temperature, water vapor and chemical substances.

軸承的性能和運行精度與標準非絕緣軸承相同.不需要額外的預防措施.

The performance and operation accuracy of bearings are the same as those of standard non-insulated bearings. No additional precautions are required.

圓錐軸承的裝配是整個裝配過程中的一個難點.首先是傳動系統的裝配.錐齒輪的預加載方式和預加載力直接影響錐齒輪的傳動狀態和整個傳動系統的傳動精度.

The assembly of tapered bearings is a difficult point in the whole assembly process. First is the assembly of the transmission system. The bevel gear pre-loading mode and pre-loading force directly affect the transmission state of bevel gear and the transmission accuracy of the whole transmission system.

性能保證了變速器的使用壽命.如果預緊力過大,可根據承載能力,、速度和工況合理設置軸承預緊力.電力消耗甚至?xí)?dǎo)致過熱.如果預緊力過小,滾動體之間的間隙和內環和外環將發生在負載的作用下,將導致傳動軸跳躍和移動,減少傳輸?shù)臏?zhǔn)確性,增加噪音,影響齒輪嚙合,在嚴重的情況下?lián)p壞齒輪和軸承.

The performance ensures the service life of the transmission. If the preload force is too large, the bearing preload can be set reasonably according to the load-carrying capacity, speed and working conditions. Electricity consumption can even lead to overheating. If the pre-tightening force is too small, the clearance between the rollers and the inner and outer rings will occur under the action of load, which will lead to the jump and movement of the transmission shaft, reduce the accuracy of transmission, increase noise, affect gear meshing, and damage gears and bearings in serious cases.

文章來自:淮安SKF軸承 -

Article from: Huaian SKF Bearing -

文章來自:淮安INA軸承 -

Article from: Huaian INA Bearing -

文章來自:淮安NSK軸承

Article from: Huaian NSK Bearing

QQ:

電話:0

手機:/