進口軸承安裝相關事項及安裝方-

imported bearing installation related matters and installation methods?

進口軸承的安裝與其自身的重要性能有關.進口軸承越重要,就越需要注意.安裝問題越清楚,進口軸承的安裝方法就越重要.進口軸承的安裝注意事項和方法如下.

The installation of imported bearing is related to its own important performance. The more important imported bearings are, the more attention they need. The clearer the installation problem is, the more important the installation method of imported bearing is. The installation precautions and methods of imported bearings are as follows.

一,、淮安INA軸承及相關部件的清潔

I. Cleaning of Huaian INA Bearings and Related Components

對于潤滑脂潤滑的進口軸承和帶油封或防塵罩的雙面軸承,安裝前無需清洗密封圈軸承.

For imported bearings lubricated with grease and double-sided bearings with oil seal or dust cover, there is no need to clean the sealing ring bearings before installation.

二.檢查相關零件的尺寸和表面處理

Two. Check the dimensions and su-ce treatment of related parts

三、安裝方法

III. Installation Method

進口軸承的安裝應根據軸承結構,、尺寸和軸承部件的匹配性質而定.壓力應直接施加在配合環的端面上,壓力不應通過滾動件傳遞.

Installation of imported bearings should be based on bearing structure, size and matching nature of bearing components. The pressure should be applied directly on the end face of the mating ring, and the pressure should not be transferred through the rolling parts.

1.壓力配合

1. Pressure fit

當進口軸承的內環與軸緊密配合,外環與軸承座孔松配合時,可先用壓具將軸承壓在軸上,再將軸與淮安INA軸承一起裝入軸承座孔中.壓裝時,將軟金屬材料制成的裝配套(銅或軟鋼)墊在軸承內環的端面上.裝配套管的內徑應略大于軸頸的內徑,裝配套管的外徑應大于軸承的外徑.內環邊緣稍微小一些,以避免對保持架產生壓力.當軸承外圈與軸承座孔緊密配合,內圈與軸松配合時,可先將軸承壓入軸承座孔,配合管的外徑應略小于軸承座孔的直徑.如果軸承環與軸和座孔緊密配合,內外環應同時壓入軸和座孔中.裝配套的結構應同時擰緊軸承內外環的端面.

When the inner ring of the imported bearing is closely matched with the shaft and the outer ring is loosely matched with the bearing seat hole, the bearing can be first pressed on the shaft with a press, and then the shaft and Huaian INA bearing are loaded into the bearing seat hole together. When pressing, the assembly sleeve (copper or mild steel) made of soft metal material is padded on the end face of the inner ring of the bearing. The inner diameter of the assembled casing should be slightly larger than that of the journal, and the outer diameter of the assembled casing should be larger than that of the bearing. The inner ring edge is slightly smaller to avoid pressure on the cage. When the outer ring of the bearing is closely matched with the bearing seat hole and the inner ring is loosely matched with the shaft, the bearing can be pressed into the bearing seat hole first, and the outer diameter of the matching pipe should be slightly smaller than the diameter of the bearing seat hole. If the bearing ring is closely matched with the shaft and the seat hole, the inner and outer rings shall be pressed into the shaft and the seat hole at the same time. The structure of the assembly sleeve should tighten the end face of the inner and outer rings of the bearing at the same time.

2.加熱協調

2. Heating coordination

通過加熱進口軸承或淮安INA軸承座,通過熱膨脹將緊配合轉變?yōu)樗膳浜?這是一種常見且省力的安裝方法.該方法適用于大擾動軸承的安裝.熱負荷前,將軸承或可分離軸承的套圈放入油箱,在80-100℃下均勻加熱,然后將套圈從油中取出,并盡快裝到軸上.為了防止冷凝后內環端面與軸肩不緊密配合,冷凝后可軸向擰緊軸承.當軸承外圈與輕金屬軸承座緊密配合時,可采用加熱軸承座的熱裝方法,避免接觸面劃傷.用油罐加熱淮安INA軸承時,應在距油罐底部一定距離處設置網孔,或用鉤子掛上軸承.軸承不應放置在油箱底部,以防止凹陷的雜質進入軸承或加熱不均勻.油箱內bi須安裝溫度計,嚴格控制油溫不超過100攝氏度,防止回火,降低殼體硬度.

By heating the imported bearing or Huaian INA bearing seat, the tight fit is transformed into loose fit by thermal expansion. This is a common and labor-saving installation method. This method is suitable for installation of large disturbance bearing. Before the heat load, the rings of bearings or separable bearings are put into the oil tank and heated uniformly at 80-100 C. Then the rings are removed from the oil and loaded onto the shaft as soon as possible. In order to prevent the end face of the inner ring from not tightly matching with the shoulder after condensation, the bearing can be tightened axially after condensation. When the outer ring of the bearing is closely matched with the light metal bearing seat, the hot charging method of heating the bearing seat can be adopted to avoid scratches on the contact su-ce. When heating Huaian INA bearing with oil tank, mesh holes should be set at a certain distance from the bottom of the tank, or the bearing should be hooked. Bearings should not be placed at the bottom of the tank to prevent sunken impurities from entering the bearing or uneven heating. The Bi in the tank should be installed with thermometer, strictly control the oil temperature not to exceed 100 degrees Celsius, prevent tempering and reduce the hardness of the shell.

文章來自:淮安SKF軸承 -

Article from: Huaian SKF Bearing -

文章來自:淮安INA軸承 -

Article from: Huaian INA Bearing -

文章來自:淮安NSK軸承

Article from: Huaian NSK Bearing

QQ:

電話:0

手機:/